DISCLAIMER

All rights of photos and text reserved. Usage of photos or text from my blog on other websites or for any other purpose only with prior permission. If you want to use any material from my blog please contact me by email.

Tuesday, July 26, 2011

Tube of the Month: The 6HS5

Hi!

This months tube is a very special type with some extraordinary properties, the 6HS5. This is a quite 'modern' tube, developed in the 1960ies. It's application was high voltage regulation for the acceleration voltage of color TV picture tubes. It was intended as a pulse type high voltage regulator.



This tube is a beam triode. This means it has another electrode between grid and plate. Similar to beam power tetrodes, it has a beam forming plate. What makes this tube so unusual are it's extremely high amplification factor of 300 together with a transconductance of 65.000 micromhos! This results in a plate resistance of about 5kOhm which makes the tube usable for LC or transformer coupling. Thus it's full amplification can be utilized.

The 6HS5 has a 12 pin compactron base. The compactron socket was introduced by General Electric. The purpose of the many pins was the possibility to integrate multiple systems within a single envelope. The 6HS5 only uses part of the available 12 pins. Control grid and beam forming plate are brought out to two pins. Only one of them needs to be connected. The beam forming plate can be connected to the cathode at the socket. There is a family of similar tube types which all share almost the same electrical parameters and have the same basing diagram: 6HS5, 6HV5A, 6HZ5, 6JD5. They only differ in the heater current and some have 35W plate dissipation instead of 30. I work mostly with the 6HS5 due to it's rather modest heater current of 1.5A at 6.3V. 30W seems ideal for the usage as an output tube. In single ended confuguration this would yield about 7W. More like 8W with the 6HV5As 35W max plate dissipation. These tubes are available in abundance from almost each reputable tube dealer at ridiculously low prices. Why are they so overlooked by the audio crowd?



Well, nothing comes for free. While the tube has exceptional transconductance paired with a very high mu, it requires a rather high plate voltage to operate. In single ended Class A, over 1000V B+ is needed to achieve sensible results. This is probably the main reason why it is not so commonly used, besides the 'TV tube stigma' which causes many very interesting tubes to be ignored by audio designers.


An important factor for audio use is the linearity. When I first discovered this tube in the tube manuals, I thought there must be some disadvantage why it is not used. It's probably not very linear. Back then I did not have any plate curves. So I ordered a few 6HS5 and tried them in a test set up. Linearity was exceptional given the other parameters of the tube. In the meantime I also found datasheets with plate curves. See picture on the right.


The curves in the datasheet compare well with my measured results. The picture below shows the plate curves of a actual tube, taken with a curve tracer. This is only a small section of the curves since the tracer only reaches about 350V. As mentioned above plate voltages beyond 1000V are needed for reasonable results. Still this small part of the curves shows that it is very well usable for audio.



Plate voltages of 1200-1300V are still quite reasonable and DIYers who are used to build with transmitting tubes like 211 or 845 can handle this. Another difficulty however is the highish plate resistance. Measurements showed plate resistances above the 5kOhms mentioned above. So an output transformer with high primary impedance would be needed. Very few such transformers exist. Suitable would be the Tango FW20-14S with 14k primary impedance, or the Lundahl LL2735B with 16k primary impedance.

The schematic on the left shows the circuit of a power amp with the 6HS5. Due to the high amplification factor, no driver or input tube is needed. This makes a so called spud amp possible with this tube. The awkward term 'spud amp' has a somewhat funny history. An amp with one tube per channel is a 'one tuber'. Tuber is also an expression for a potato. That's why these amps are also called potato amps sometimes. And spud is just another synonym for potato. So all which is needed is the output transformer, a cathode resistor with appropriate bypass cap and a high voltage supply. The schematic also shows a decoupling choke and the decoupling cap is connected in ultrapath fashion, my favorite topology for transformer coupled stages. The tube operates at about -3 to -3.5V grid bias. So up to 7V peak to peak input voltage is needed for full power out. That's about 2.5V RMS. A bit above the typical line level, so it is preferred to drive such an amp from a pre amp with some gain. Below is a photo of a single ended power amp using one 6HS5 per channel:



This circuit can be easily scaled up to achieve more power by paralleling tubes. A Parallel Single Ended verison with two tubes per channel delivers twice the power:


This scheme can be even scaled further. Below a photo of Quad Parallel Single Ended mono blocks. These deliver solid 30W single ended pure Class A:



Close up photos, showing the glow of the tubes. The blue glow is normal and does not indicate bad tubes:



I will cover details about this family of amplifiers in an upcoming series of posts. But the 6HS5 is not only suitable as output tube. I already introduced it as a driver tube in my recent 211 amp. Here the high B+ voltage is already available in the amplifier, since the 211 has a similar B+, so the plate voltage for the driver could be derived form the output stage through a separate choke and decoupling capacitor. Other applications are possible as well. I have successfully used the 6HS5 even in phonostages. Both in single ended and fully differential configurations. Some care is needed to control microphony in a phonostage and it needs well filtered B+ and DC heater supplies in this application. But it is managable. A very versatile tube which provides many possibilities of use for creative DIYers! But how does it sound, you might want to know. The sound of an amp is not determined by the tube alone, but the whole concept. A simple circuit like this has much less parts in the signal path which can alter the signal. This gives the chance to build a very direct sounding amp with high resolution. Kind of like a single chassis speaker without crossover. The 6HS5 does not have the refinement and ultimate musicality of a directly heated triode. But it compensates a lot by the complete lack of a driver stage. Since it uses so few parts, better parts can be chosen and in fact this is mandatory to achieve a good result. The sound of the amp is ultimately determined by the tube, the output transformer and the ultrapath cap. Due to the low part count excellent results can be achieved with a moderate budget. An amplifier with directly heated output tube and the same power rating would require to spend at least 3 times as much on parts to surpass the sound level of such a 6HS5 amp. Since it is indirectly heated no elaborate filament supply is needed. It can be AC heated without any hum. In single ended configuration a well executed 6HS5 with a top quality output transformer like the mentioned Lundahl and paper in oil capacitors gives a very nice mellow tone with little coloration not very different from a 45, but with more power.

This tube would actually also be quite suitable for a multi channel amp or for an active system. Multiple 6HS5 amps which share the same PSU can be easily integrated into a single chassis. I did build something like that for the European Triode Festival 2004, 4 stereo amps (8 channels) in a single chassis for a 4 way active speaker. This consisted of 4 SE amps using one 6HS5 each, two PSE amps with 2 tubes each and 2 parallel push pull amps with 4 tubes each. Even the linestage was integrated using yet another 6HS5 per channel. So 18 6HS5 tubes in a single chassis. The photo on the left shows an impression how that looked like.

If you find this tube interesting and plan to build an amp with it, you should be aware of the dangers of the high voltage this tube requires. Only attempt to build such circuits if you have experience with high voltages. It is important to ensure proper creepage and clearance distances. Voltages over 1kV can 'jump' over small distances of air. For this reason I do not mount the sockets for the 6HS5 directly to metal plates. They are recessed below the plate. In addition I always drill the unused pins out of the socket. These are the pins 5,6, 8 and 9 which are on both sides of the plate pin 7.  Also the internal wiring of such an amp needs to be carefully isolated. Addtional insulations sleeves over all wires carrying high voltage are recommended. Keep in mind that the plate swings far above the B+ voltage coming from the PSU when the tube is driven to full power. If the necessary precautions are taken, the 6HS5 will deliver excellent performance. It is very tough and will last long even when operated at it's plate dissipation limit. The tube seems also suitable for Class A2 operation with the grid being driven into the positive region. This way it can also be used with lower plate voltages. However I have not explored this myself yet.


Stay tuned for upcoming articles around this tube!

Best regards

Thomas

22 comments:

  1. Hi Thomas.
    This tube looks like a good candidate to direct drive an electrostatic speaker. Maybe just the treble panel of a hybrid ESL. A differential SRPP pair consisting of four tubes per channel with +/-1200V bipolar power supply might do the job. Filaments will need separate floating power supply. I have been planning to build a direct drive electrostatic headphone amp for Stax. I had 6S4 or 6AH4GT in mind. 6HS5 might be easier to implement with just two stages and enough gain for feedback.

    ReplyDelete
    Replies
    1. Hi!
      Please keep me updated about your results if you try this

      best regards

      Thomas

      Delete
  2. Does exists similar, in small package, weaker?

    ReplyDelete
  3. Thomas might there be sonically interesting line level applications for this tube at much lower voltages? Maybe 250v based on your curves?

    ReplyDelete
  4. Hey just wanted to say I think your talented builder and look forward to reading more of your site
    Now with that said where can I buy these tubes at ridiculous prices? If I can find them for a buck each I would buy 100

    Lawrence

    ReplyDelete
    Replies
    1. If you want ridiculous prices you need to search and be patient. Normally they are offered around $5-$8 which is still ridiculously low for such a piece of technology

      Thomas

      Delete
  5. I would disagree these are not rediculious cheap a dollar a piece is more like it :)

    ReplyDelete
  6. I have been tested 6hv5's beam plate connected plate , or connected to cathode . I don't find much of difference with sound. How do you think ,it is better to connect with plate or cathode?

    ReplyDelete
    Replies
    1. This comment has been removed by the author.

      Delete
    2. I never tried beam plate connected to anode.
      Only connected to cathode

      Delete
  7. Hi
    In article above written by you "The beam forming plate can be connected to the cathode at the socket. ". It is right?

    ReplyDelete
  8. This appears to be the ideal valve to drive a Pair of triode strapped 813.

    Interesting,the cavity anode design was the last development of the very last units.

    The more fragile 8417 was done this way, and also has very high gain.

    ReplyDelete
  9. Hi Thomas,
    What about a PPP amp based on the 6HS5 with a phase splitter trafo at the input? What Lundahl would you recommend for the job? It seems like otherwise we could adapt your SE schematic.

    ReplyDelete
    Replies
    1. Hi!
      I have not worked with the 6HS5 for a while. It has very high plate impedance so even a PPP amp would require OPTS with very high primary impedance. Maybe the LL1691B would work

      BR

      Thomas

      Delete
  10. I am making KT150 CSPP amplifier, using 6HS5 as a driver with anode choke PP drive. CSPP requires quite a high driving voltage so I hope to use 6HS5 600v on plate. I don't know if it is high voltage enough for 6HS5 ? I am going to try.

    ReplyDelete
    Replies
    1. I don't think that will be enough in order to get the output voltage you need

      Delete
  11. This was a very interesting thread.
    May be interesting to note it's extremely easy to find a HT source to power a few of these.

    Just find a couple of microwave oven transformers.
    You can choose to run 230V ones in series to halve the output and/or give a centre tapped +/- supply rails. Very cheap and powerful.

    ReplyDelete
  12. How about a cathod follower to drive speker via more common xfrmr?

    ReplyDelete
    Replies
    1. you can try that, but you will need a second stage to provide the large drive voltage needed

      Delete
  13. I have used the 6HS5 as a dc coupled deflection amplifier, It worked great and we sold a few. The biggest problem was a low capacitance heater winding. Transformer winders would not understand that air in the winding was a must. We got part of the way but never much beyond 5kHz because of the capacitance of the heater winding. We used -2500V to +2500V and the output swung +/- 2000V. the standing current was 11mA, so the tubes dissipated 28W all the time. It was all class A and lots of negative feedback, probably 50dB or more. H J Weedon

    ReplyDelete