DISCLAIMER

All rights of photos and text reserved. Usage of photos or text from my blog on other websites or for any other purpose only with prior permission. If you want to use any material from my blog please contact me by email.

Saturday, March 12, 2011

Making of a 211 Amplifier, Part 1: Planning

Hi!

Ever since I started building tube amplifiers, the 211 was among my favorite tubes. In fact the very first power amp which I built used the 211 as an output tube. This first amp evolved through several stages and finally ended up in huge monoblocks with 211 drivers and even bigger 3 phase power supplies. Those of you who are familiar with the Sound Practices magazine might have read my articles about this amp and the 3 phase power supplies.

After I started to go commercial with my amplifier designs, I decided to build a scaled down version of this amp. It used a single phase supply, and a smaller but still directly heated driver, the 801A. Power supplies were still external so that the whole amplifer ended up in 4 chassis and has a weight of more than 100kg.

This is a photo of one channel of the amp:


Tango interstage and output transformers, NOS paper in oil caps in the power supply. DC heating for both driver and output tube using a purely passive LCL filter per tube. The sound of this amp is excellent and very close to that of the bigger one with 211 driver. The amp was publicly demonstrated at the ETF 2009 in Stella, France. Yet for many the sheer size of this amp with 4 chassis in total is a bit overwhelming. Here is a photo of the complete set:


The 4 chassis in the front row are just one stereo amp!

Also the cost of such a 4 chassis beast is quite high. The use of the finest Tango transformers contribute a good part to the overall cost. Also quite significant the expense of 4 chassis. Since the 211 is operated at max B+ voltage, very high quality umbilicals and PSU connectors need to be used which are rated for the voltage, again a cost driver. Yet the 211 and 845 tubes are quite popular and many people need more power than can be obtained from smaller tubes. So the idea for a yet further scaled down 211 came up. The actual development of a smaller version was triggered when Lundahl announced the availability of a new output transformer with a high 20k primary impedance, the LL1691B. Twice the primary impedance of the 10k which is commonly used in 211 designs. This should ensure a more linear operation of the output tube and provide a lower output impedance.

As mentioned above a big cost driver are the 4 chassis. Also the elaborate power supply with choke input filtered B+ and separate DC supplies for output and driver tubes. Some simplification is necessary there. Of course a good way to make the amp simpler is the use of an indirectly heated driver. Possibly a similar architecture as presented in the single ended amplifier concept series. This means a two stage approach. While this is fairly easy with smaller triodes, it is more of a challenge for a 211 if the same level of gain and headroom shall be reached.

Since I already had good experience with the 6HS5/6HV5A family of tubes as output triodes (this will be coverd in upcoming articles) I always wanted to use them as drivers too. They have an extremely high amplification factor of 300. Their plate resistance is still in a range which enables transformer coupling. See the datasheet for details. The amplification factor is even high enough so that the interstage transformer can be wired as step down. This should give a nice low impedance driver which even allows the 211 to be pushed into Class A2 territory. A suitable interstage transformer can also be found in Lundahls portfolio, the LL1660/25mA. Even if the interstage is wired in 4.5:1 the overall gain is still enough so that no input transformer is needed as with the 801A/211 or 211/211 versions. This makes the design more widely usable with almost any preamplifier.

Normally the high plate voltage requirement of the 6HS5/6HV5A is a disadvantage but since we already have B+ in the range of 1300V for the 211, the supply voltage for the driver can be derived from the 211 output stage B+ via a separate LC decoupling stage. This further simplifies the amp.

No compromise should be made in terms of capacitor quality, so no electrolytics in the B+. Also the amps should be as hum free as possible, which makes DC filament supplies necessary for the output tubes. Since the DC filament supply has a massive impact on the sound quality, no other approach than the well proven passive LCL filter is considered.
As mentioned above, a big cost driver is also the choke input supply for the B+. Especially at these high voltages very massive input chokes are needed since they have to withstand a large AC voltage amplitude across them. Therefore another approach will be used. A voltage doubler supply, but with tube rectification. This enables the use of an existing power transformer, the 400mA universal B+ transformer as was shown in my article about power transformers. Since the driver tube has a compactron base, a TV damper with the same will be used for the rectifiers, the 6CG3. The 6CG3 is one of the strongest TV damper tubes. It is capable of 350mA DC each. In a bridge configuration two of these can deliver 700mA! In a voltage doubler arrangement, each rectifier has to deliver the full current which is consumed by the load, still the theoretical maximum of 350mA which two 6CG3s can deliver in a voltage doubler is more than adequate for a mono amp.

This leads to a design which is outlined in the schematic below:



Although this is a 'scaled down' amp it is still a beast, 4 transformers (output, interstage, B+ and filament) 5 chokes (2 filament, 3 B+) and a large array of paper in oil caps per channel. For the oil caps the same 5uF/2kV types as in the 4 chassis amp will be used. Each 10uF cap value in the schematic will be done with two of them in parallel. No way all these parts would fit into one chassis for a stereo amplifier. The concept will be built up as mono blocks.

In the second part the assembly process will be shown. Stay tuned.

Best regards

Thomas




15 comments:

  1. Thomas, very interesting article and design.
    I am interested in audio, and have been looking over 211 SE amp schematics recently, and came across this page.
    I have been aware of the 6HS5 and I have at least two of them, and aware of the unusually high gain, I don't remember seeing anyone use them for audio.
    And your use of the TV dampener tube, 6cg3, another interesting possibility.
    I will have to remember to get back to this page to see the 2nd installment.
    Thanks,
    Leslie

    ReplyDelete
  2. Hi Leslie,

    the second and third intsallments are already written. I finished the amps. Click on the 211 label in the column on the left to see all articles related to this amp.

    Thomas

    ReplyDelete
  3. Great, economical amp design, in terms of part count. The 6HS5 as a driver for big tubes seems to need an inter-stage or a plate choke, which really shoots up the price. Do you know what the lowest voltage the 6HS5 can be operated at without sacrificing gain, sonics, etc.?

    Joe

    ReplyDelete
  4. Hi Joe,

    amps with big tubes tend to become costly anyways, so a good interstage or plate choke should not be a big factor. Especially with big output tubes, you want to run some current through your driver. If you operate the 6HS5 at 600V you either will have very little current through it, or you have to run the grid at such a low bias voltage that you have little headroom. Either is a poor compromise IMHO.
    I got best results when running it at 1kV+

    Best regards

    Thomas

    ReplyDelete
  5. I use a simpler design-less iron:Monos- 6BM8-NC-14-RS-237-Tango 10K. 4-6CJ3 dampers, 20hy choke,current regulation on RS-237, 5-LCR caps, dc on driver, custom PT with 13 volt winding for regulation circuit, all on one chassis. 980v/50ma.Best sonics at this current. Using Uno's 3.0-Dead quiet. Filament ramps up slow. Hugh sound stage. Low cost

    ReplyDelete
  6. Hi!

    I purposely avoided current regulation since I prefer the sound of purely passive filament supplies. That's why the many chokes are needed. In terms of signal path it is as simple as you can get a 211 amp. I also find it preferable to have the filament supply fed from a separate transformer.

    Best regards

    Thomas

    ReplyDelete
  7. I can't comment on the difference in sound with my amp since I have not tried your design, but I have used it in another design and prefer heaters current regulated. I find metal plates sound better than carbon. Like WE-242C and Telefunken RS-237 which I now use. Current regulation preserves the filament integrity of this pricy tube, increases dynamics & sound stage and as in my reference CD Bach Secular Cantatas-Dorian RR-S3CD Tract 9-11. Nobu Shishido was commenting on current regulation before he died.

    Thanks--

    ReplyDelete
  8. Hi!

    I did the comparison. I tried a lot to sort out the ideal filament solution. This is especially critical with directly hetaed preamps. Based on my work I prefer the passivle solution with LCL filter (no final C). If budget or space does not permit the useage of filament chokes, current regulation is the choice.

    Best regards

    Thomas

    ReplyDelete
  9. Hi!
    I will try the passive with the LCL filter.Also try a RS-237 metal plate triode.

    Thanks--

    ReplyDelete
  10. Hi Could You please share the Output transformer Primary inductance [Hy], and Primary capacitance?
    Thanks

    ReplyDelete
    Replies
    1. Hi! There is a link to the transformer data sheet in the post

      Delete
  11. Good morning, Mr Mayer,
    just a question, wanting to use the fixed bias, instead of the usual resistance cathode on the valve 211, the "ULTRAPATCH" configuration is equally applicable.
    Thank you ,
    Greetings,
    Andrea

    ReplyDelete
    Replies
    1. Hi!
      ultrapath is only applicable with cathode bias resistor

      BR

      Thomas

      Delete
  12. Hi Thomas,

    You take step down transformer for interstage for keeping Zout low as possible. Very good design! But, in cathode bias, grid 211 is always zero volt DC. Does 211 run to A2 class? If so, how do we know that?

    Thank you.

    ReplyDelete
    Replies
    1. Hi!
      The driver can drive the grid into the positive territory. However my intention was not to build a Class A2 amp. If you want a proper Class A2 amp you need to design for it. The driver stage in this amp just give a little extra headroom since it does not immediately clip when the grid goes positive.

      Delete